What cylinders will fit my hobbit 2? (9 replies)
Hi, my hobbit cylinder is badly scored and a exhaust bolt is stuck so i thought its time to get a new cylinder, i would like a 70 kit but im in england so shipping would cost too much as most parts...
View ArticleE50 clutch (2 replies)
Hi so I am rebuilding my engine, I got the Airsal 70cc kit, but I forgot when I was ordering to look at my clutch but I did buy the blue springs, but my clutch it the 2 shoe type should I upgrade to...
View Articlebetter brakes for puch magnum (2 replies)
hello has anyone ever done some sort of front wheel swap on a magnum. i have tried a couple different company brake shoes but i still feel the brakes aren't strong enough it takes to long to stop and...
View ArticleEstoril w/ rear bleed mounting help on Maxi frame (2 replies)
Any tricks getting an Estoril with rear bleed to mount onto a Maxi? I drilled out the holes a little already. Looks like I need to grind down the welds around the pipe so that I can get the nuts to...
View ArticleMotobecane two gear clutch (Variator) (no replies)
It engages instantly into second gear as soon as throttle opens. It has been modified with tighter springs and shaved pads but still engages way to early. Running it with Airsal 75cc/dellorto19mm/cdi...
View ArticleMotobecane gas strut preload? (no replies)
I'm installing a gas strut on my av10 build and had a question that I can't seem to find an answer on. Is it necessary to preload the gas strut by mounting it so that it's partially compressed at...
View ArticleAirsal 65cc jet selection (3 replies)
Ok...so I know this topic has been beat to death but I'm still gonna see if I can pull the experts out of the woodwork. For the record...I've searched, found, and read other similar posts as well as...
View ArticleAmal 15mm cable bendys removeable? (no replies)
Are the Amal 15mm cable bendys removeable and replaceable with the standard dellorto/Mikuni threaded cable bendys? May need to use 45 degree rather than the provided 90 degree choke and throttle...
View ArticleToo short variator belt ok? (10 replies)
Got a new belt for my Spx today, the old one is to short, of course this new one is too long and unusable... I'm trying to get my head around if running the too short belt is dangerous or not....
View ArticleClik here to view.
Stock E50 1HP CYL. Top Speed? (11 replies)
No Bullshit. I have a Pinto with a stock pipe and cylinder that rides 50+ mph gps verified. All day long. I installed an inner coil ignition because the stock ignition took a crap and my Tillotson...
View Articlemotobecane spark (1 reply)
So my av7 has a kit carb and pipe with new le partie cdi. I have timed it and has no spark at all. What could be hold it back from firing?
View ArticleTell me how fast. (20 replies)
I think I have a pretty good idea what the top speed will be, but lets hear opinions people the setup my LENGENDARY 1980 Honda express II na50 81 nx50 engine 14 inch rear wheel! with stock nx50...
View ArticleCamino VS Hobbit rear variator spring rate (1 reply)
I've searched and couldn't find much comparison on the camino and hobbit rear variator stock spring rates. I will be running a TJT/DR setup and I know there are hobbit contra springs (yellow and red)...
View ArticleISO Water Pump Bosch/Whatever (7 replies)
Looking to see what people have used sucessfully. I was thinking I was going to thermo-siphon but may have to just switch to 12v and add a pump. OR just a battery, how many amps could it draw.
View Articlepuch maxi moped 70cc kit parts, does anyone have experience with boring...
hey guys, I have decided to upgrade my puch maxi to a 70cc kit, i am looking for any advice on what people this the best combination of parts to use to really get it going around 45mph. i have...
View ArticleTomos Disc Brake Squeal - EBC pads (10 replies)
I have tried everything with my Tomos to get the disc brake not to squeal. I've sanded the pads, beveled the pad edges, cleaned the pads with brake cleaner, routinely cleaned the rotors with brake...
View ArticleTreats reed kit temperature (11 replies)
What kind of temperatures are you guys cruising at with the treats reed kit? On my setup at WOT I've hit 440 degrees going 50mph on the flats. Treats reed kit 70 hi comp head VM20 with 170 main and...
View ArticleRiding mopeds with studded tires in the snow? (7 replies)
I live in NJ and 2m we are too get 12 inches of snow andddddd we have two motobecanes with knobby/studded tires how you guys think this is gonna work out? LOL my prediction is that the bikes will GO...
View ArticleOmaha 80cc Trail Master 1966 (2 replies)
Hey guys I apologize as this is not a moped, albeit it looks like one. I have a Yamaha mg1-T and the manual says to use 20 : 1 two stroke oil, the fresh rebuild and new piston and rings. I have the...
View Articlebreak in new 70cc kit (7 replies)
hey yal, i just got a 70cc kit from treatland, piston, exhaust, and carb. im wondering what people think the best way to break it in is. i have been told not to take it over 35mph for about 100 miles....
View Article