Tach hook up to a 12v puch ZA50 powerdynamo CDI - 12v / 100w (2 replies)
I bought one of those 12v cheap ebay tachs to install on my za50 and I have the 12v powerdynamo CDI. According to the CDI wiring, it says to connect the pick up wire to the blue/ignition switch lead...
View ArticleClik here to view.
So any old ignition coil will do for cheap cdi? (3 replies)
So I need to confirm this trick works after I just got this $10 ignition coil from China after someone absconded with my old one. It's for a cheap cdi of the stars type (non combo so separate cdi box)...
View ArticleTuning my moby (1 reply)
Rebuilt my '77 50V engine with an airsal performance crankshaft, new bearings seals and gaskets, airsal 74cc (47mm bore) top end, timing set to 1.4mm BTDC, currently running a 78 jet in a 15.15 sha...
View ArticleToo big a Carb?? (2 replies)
I have a what I believe to be a Vm26 carb is this carb too big to pair with a 70cc Malossi Pa50ii Kit paired with a ppl did bleed pipe . It was either this carb or a 16:16 Sha that I have also trying...
View Articledownjetting???? (1 reply)
minarelli v1 77 race cranks 21mm phbg slanted angle kinda facing forward wth no air filter 80cc polini 92 jet i am running rich afaik i change the spark plug almost every week anyways just bought two...
View Articlehows the tune on this ped sound? (4 replies)
video: <iframe width="560" height="315" src="; frameborder="0" allowfullscreen></iframe> gila 74cc 19mm carb estoril pipe points fat gap timeing retarded almost fully im going to try...
View ArticleWill IRC NC 77 80/90x14 work on qt50? (no replies)
I'm wondering if this will work as the rear tire for the qt50. I know the 70/90 does. I imagine the stock rear fender will have to go. Will 10 more mm be too much for the rim? Anybody tried?
View ArticleMods to my magnum but something feels missing (4 replies)
I kitted my bike with a 15mm bing 64 jet, ported 14mm intake, ported the head on the intake. I machined the head flat and have a very thin headgasket. 12v cdi kit. New piston and rings and Jammy pipe....
View ArticleFront forks issue (2 replies)
I go to see why my front Puch Magnum forks are and have been a little too stiff so I took a break down of how to shocks looks to a hydrolic professional and he said to put in a thinner oil and see how...
View Articlefa 50 head (2 replies)
What heads besides the fa head would fit. Would a puch head or Honda head fit?
View ArticlePeugeot 103: DIY Rubber Motor Mounts (no replies)
I've been experimenting with these for about 2 months now and decided that it's time to share and hopefully get some user feedback. Personally I've experienced approximately a 40% decrease in overall...
View ArticleWill this exhaust mod make any difference? (3 replies)
I've got a Puch free spirit with a 6port 50cc kit on it. The kit has got a larger exhaust outlet port than the stock exhausts intake. Right now, funds are not permitting a new exhaust, but if I ground...
View ArticleFriends Garelli sport ideas (3 replies)
My friend has had this Garelli sport since new and I just got running and it runs well. The problem is that it is a super slug. I know what to do with my Puch but don't know much about the Garelli....
View ArticleVM20 on an Urban Express (4 replies)
So I have an Urban Express and a Mikuni VM20. Express is only lightly modded, People's Pipe, BX31, 3x stock variator weights and a GY6 clutch. Stock carb, Keihin 85 jet. I get about 36 mph. I think...
View Articlev1 + MLM peoples + Polini 15mm jetting (5 replies)
I'm looking for any advice on jetting a stock v1 with MLM people's pipe and 15mm Polini. Once I get it running to tune it... Swapped out the pipe and it won't fire up now with either stock 12mm del...
View ArticleRebuilding Korado E50 issues (no replies)
I have a Korado kickstart I'm rebuilding and I'm finding some play on the main shaft. It is a three bearing motor with the main gear having only one bearing and a blind hole in the case for the other...
View Article27 tooth front sprocket on Tomos (no replies)
While waiting for my clutches to be Kevlar lined, I decided to put a 27 tooth front sprocket on the A55. What a pain. I thought there would be a small amount of grinding needed to the cases but it...
View ArticleE50 will not start...... (1 reply)
I have an E50 with a 65cc Hero kit, 16mm PHBG and MIM pipe. Spark is good, NKG B6HS, carb has 74, 60, 48, float is at 16.5. New gas, 50/1. Plug gets wet in time. It ran for 15-20 seconds, then poped...
View ArticleSquish band, polishing and skimming head (8 replies)
I decided to go ahead and rebuild the top end on my Kinetic motor. I rebuilt the bottom end but couldn't get it to run despite having 110 lbs of compression. Well will run at WOT with the choke on for...
View Article