Clik here to view.
Peugeot SPX Artek Nut (4 replies)
What nut goes on the variator size of the Peugeot SPX Artek crank? I searched and found its M10x1.25, anything from another moped/part that has an easy fit? Cant seem to find the right one so far. Thx
View Articlesuzuki or50 bearing noise (no replies)
so I have this 50 shifty Suzuki or50 starts first kick, runs great, ive driven it about 120 miles thus far no issues however when its running instead of just hearing the "put put put" from the exhaust...
View ArticleFA50 jammy exauhst header fitment (1 reply)
Hello, i just purchased a fa50 and am working to restore and tube it. While starting to lean my exauhst i found that the baffle? Or big part of the muffler has seperated all the way around the weld...
View ArticleMoby head modification (2 replies)
I am installing a 74cc Airsal 47mm kit on my moby. I'm a little unclear as to what I need to do to the head to make it fit. Found an article in the wiki but I'm not sure if that applies to the...
View ArticleStud spacers (5 replies)
I just bought 2 pairs from treats, what are the benefits besides less slop?
View ArticleQt 50 main jet (no replies)
I'm trying to find a new main jet for my qt50 looking to go to a different size since I've put an air filter and am waiting to get an exhaust upgrade. I already ordered some but they were too small if...
View ArticleVarplus issues with sticking open (6 replies)
So does anyone else have issues with the motobecane Varplus sticking open once it gets to full variation? Mine seems to want to stick open, then will kinda jump back down once I'm slowing down very...
View ArticleVariatior mod what is it? (3 replies)
It looks like it's been cut and ground to seat lower.
View ArticleHow to get more low-end power, Sachs 504 (1 reply)
I've pretty much completed converting my Westlake's 504/1b to 504/1a configuration. Mods to date include 12 mm square bing, opening up the exhaust port in the cylinder, and adding the larger-diameter...
View ArticleFuel Tank Liner (4 replies)
I was having some difficulties with rust in the gas tank. Got it looking good using the vinegar method. I got some Red-Kote Fuel tank liner and now I wanted to know some peoples opinions about just...
View Article70cc non reed treats kit on za50 still TOO SLOW (13 replies)
It's running ok. I need to up the idle jet on the 19mm phbg and grind out some more of the stator for timing but it's still running too damn slow. Let me make clear that I am 6'2 230 so that's...
View ArticleTK turbo exhaust for Mobylette (no replies)
I need some help. So I am attempting to install a new TK turbo exhaust onto my Moby. However, it seems like a real pain in the ass trying to get the engine disassembled in order to actually be abe to...
View ArticlePuch RPM range (1 reply)
Hi, can anyone give me an idea of what the rpm range is for a stock E50 Puch engine & gearing please? Not looking for exact figures, just a rough idea. Cheers.
View ArticleShaking, bogging in second gear (no replies)
Got my moped running finally. But it bogs and shakes when it shifts into second gear. Has fresh tranny fluid in it.
View ArticleDerbi Pull start (4 replies)
Question about pull starts. I have a pull start on an SLE Flat Reed Variant. It did not come with instuctions, or gaskets. When I initially put it on without gasket, it would pull, but not spring...
View ArticleRemoving silencer? (9 replies)
Any negative effects that would come from removing the silencer from my tecno circuit? I know it will be louder but will it cause and issues?
View Articlemorini dudes: assemble! (2 replies)
just won a pacer this weekend at the no-nos rally. specs: mo2 stock clutch springs polini reed kit 16 sha (somehow it idles) mk3 pipe needle crank (stock) dinosaur head glued to speedo what should i...
View ArticleA35 idles high and cuts out around 35ish? (no replies)
A35 70cc airsal, MLM intake, vm18, boss pipe. My timing was advanced all the way so I moved it to half way, no air leaks, adjusted my needle two notches higher. The idle screw does nothing and the my...
View ArticlePuch no torque (1 reply)
I have a puch maxi 1.5hp fully stock. Bought it non running from a guy, went through took everything off and cleaned it to a shine changed all gaskets and wiring is all good. starts up first kick and...
View ArticleHow to rig up pedals on a noped? (3 replies)
Anyone ever scab pedals onto a noped to slip in under the law? I've got a 2-speed Garelli VIP moped. They sold kick-start pedal-less 3- and 4-speed manual shift versions of the motor in Italy. I found...
View Article